{{ name }}
Nr art. {{ combinedCodeWithHighlight }}
Nr własny produktu:
EAN / GTIN:
Numer producenta:
Nr katalogowy:
UCI Hardness Tester HO 1K, hardness scale HV 1 10 N, Probe length 18 mm
Nr art.: HO 1K
Nr własny produktu:
UWAGA:
Ten produkt jest zamawiany bezpośrednio u producenta i nie znajduje się w naszym magazynie – czas dostawy może być wydłużony.Ostateczna cena zostanie wyświetlona po dodaniu produktu do koszyka i przejściu do kasy.Produkt nie podlega zwrotowi.
InformacjeSzczegóły produktu
Dane techniczne
| Czas pracy | 12 h | |
| Czas ładowania na akumulator | 8 h | |
| Opakowanie | walizka | |
| Zasilanie energią | Zasilanie akumulatorowe | |
| Metoda pomiaru | Vickers | |
| Skale Vickersa | 1 599; 80 | |
| Główne obciążenia naciskiem pomiarowym | 10 kg | |
| Rodzaj produktu | twardościomierz | |
| Długość całkowita | 160 mm | |
| Szerokość łącznie | 83 mm | |
| Wysokość całkowita | 28 mm | |
| Masa | 0,5 kg | |
| Norma | DIN 50159-1 | |
| Złącze | USB | |
| Z wyświetlaczem | tak | |
| Przechowywanie wartości pomiarów | tak |
Identyfikacja i klasyfikacja
| Numer artykułu | HO 1K | |
| EAN / GTIN | 4045761184138 | |
| Numer producenta | HO 1K | |
| Numer L | L40250 1753 | |
| Producent/osoba odpowiedzialna | Kern & Sohn GmbH, Ziegelei 1, 72336 Balingen, Deutschland, www.kern-sohn.com |
Opis
Opis:
- Application: This ultrasound hardness testing device is ideally suited for mobile hardness testing, where the main emphasis is on obtaining rapid and precise results
- Standards: The device meets following technical standards: DIN 50159-1
- Mini statistics function: Display of the measuring result, the number of measurements, the maximum and minimum value as well as the average value and the standard deviation
- Advantages compared with Leeb: The high requirements for the weight of the test object are no longer required, in most cases
- Principle: The SAUTER HO measures by using a vibrating rod which vibrates at ultrasonic frequency and is pressed onto the sample at a defined test force. At the lower end there is a Vickers indenter. Its resonant frequency increases as soon as an indentation is created when it comes into contact with the sample. Through appropriate adjustment of the device, the resulting change in resonant frequency is matched with the corresponding Vickers hardness
- Examples: The HO ultrasound hardness testing system is primarily used for measuring small forgings, castings, welding points, punched parts, casting tools, ball bearings and the flanks of gear wheels as well as for measuring the influence of warmth or heat
- Measurement data memory saves up to 1000 measurement groups each with 20 individual values
- Advantages compared with Vickers: Demanding optical measuring is not required. You can therefore carry out measurements directly on-site, for example, on a permanently installed workpiece
- Calibration: The device can be set to both standard hardness test blocks and also to up to 20 reference calibration values. When doing this it is possible to measure different materials quickly, without having to re-adjust the device to the individual materials
- Advantages compared with Rockwell and Brinell: Means that the testing is almost nondestructive, small penetrations means that the testing is less destructive
- ASTM-A1038-2005
- JB/T9377-2013
- Scope of delivery: Standard block for calibration (approx. 61 HRC), USB cable, Display unit, UCI sensor unit, transport case, software to transfer the saved data to the PC, accessories
Cecha szcz.:
- ± 3 % HB
- HV: 80–1599
- ± 1,5 HR
- HRA: 61-85,6
- Minimum weight of the test object: 300 g for direct measurement with the sensor (included)
- Internal rechargeable battery pack, operating time up to 12 h without backlight, charging time approx. 8 h
- HRB: 41–100
- Measuring time: adjustable from 1-5 sec
- Measuring ranges: HRC: 20,3–68
- Display units: HRC, HV, HBS, HBW, HK, HRA, HRD, HR15N, HR30N, HR45N, HS, HRF, HR15T, HR30T, HR45T, HRB
- Tensile strength: 255–2180 N/mm2
- Measurement precision: ± 3 % HV
- HB: 76–618