{{ name }}
Article no. {{ combinedCodeWithHighlight }}
Article code:
EAN / GTIN:
Manufacturer number:
Cat. No.:
HiPer Drill base body, 3×D, ⌀ DC: 18mm
Article no.: 231605 18
Article code:
Product details
Technical Data
| Series | HiPer-Drill | |
| Number of cutting edges, total | 2 | |
| Cutter diameter, min. Dc | 18 mm | |
| Overall length L | 142 mm | |
| Usable length L1 | 57 mm | |
| Gauge length A | 86 mm | |
| Shank diameter DS | 25 mm | |
| Through-coolant | yes | |
| Holder type | plain shank | |
| Entry of cooling lubricant | with cooling lubricant entry, axially concentric | |
| Interface position | on the machine | |
| Interface coding | ZYL02501015 | |
| Holder version | metric with cooling lubricant holes | |
| Holder size, metric | 25 mm | |
| Holder tolerance class | h6 | |
| Length of shank LS | 56 mm | |
| Cooling lubricant | yes | |
| Manufacturer’s designation | HiPer Drill Grundelement | |
| Cutter diameter, max. Dc | 18.99 mm | |
| Flute length | 57 mm | |
| Distance from cutter corner to cutter tip | 3.2 mm | |
| Attachment length, holder | 69.3 mm | |
| Twist angle | 13 degrees | |
| Adjustment range | setting not possible | |
| Angle, 1st step | 135 degrees | |
| Interface | joint 1 | |
| Insert thickness T | 6.5 mm | |
| Type of fastening for insert | P (with cyl. hole clamped via hole) | |
| Interface coding for insert | HOG-2316xx180 | |
| Insert designation | 231640 18 | |
| Weight | 274 g | |
| Cutting direction | right-hand cutting | |
| Machining method | drilling into solid material (BVB) | |
| Type of product | indexable drill for cutter inserts | |
| Bohrtiefe für Wendeplattenbohrer bis | 3×D | |
| Use for drilling | limited cross-drilling; limited drilling through a stack; limited drilling with oblique exit; limited oblique spot drilling | |
| Content | single part |
Identification & Classification
| Article number | 231605 18 | |
| EAN / GTIN | 4045197602794 | |
| Manufacturer number | 231605 18 | |
| Manufacturer/responsible person | Hoffmann Supply Chain GmbH & Co. KG, Poststraße 15, 90471 Nürnberg, Germany, www.hoffmann-group.com |
Description
Version:
- Very high feed rates and maximum performance due to optimally matched geometries and materials.
- Precise positioning of the cutter insert due to Vee insert seating and secure clamping by the centre bore.
- High concentricity when assembled. (For holes up to IT9 accuracy)
- Shank support for optimum stability in operation.
Application:
For stationary and rotating use. For holes up to IT9 accuracy.
Note:
The insert screw must be replaced after every fifth change of cutter insert.
Further sizes up to ⌀ 50.99 mm available on request.
Clamp in a hydraulic chuck (such as No. 302026 size 20) for optimum radial run-out.
For optimum stability, clamp the drill so the overhang is as short as possible.
Further sizes up to ⌀ 50.99 mm available on request.
Clamp in a hydraulic chuck (such as No. 302026 size 20) for optimum radial run-out.
For optimum stability, clamp the drill so the overhang is as short as possible.
Warning:
Intended use
Reasonably foreseeable misuse
- For stationary and rotating applications.
- For medium-sized bores up to IT9 accuracy, right-hand cutting.
- Only use with cooling lubricant emulsion for through-coolant.
- Carry out pilot drilling before use to increase process reliability.
- Use only with cutter insert no. 231630 – 231690, clamping screw no. 231999.
- Tighten clamping screw with torque engraved on drill.
- For work in industrial environments.
- Use only when it is technically in good condition and safe to operate.
Reasonably foreseeable misuse
- The operating company must ensure that personnel who work on the product comply with the regulations and provisions together with the following instructions: National and regional regulations for safety, accident prevention and environmental protection regulations.
- No damaged products are assembled, installed or commissioned.
- The necessary protective equipment is provided.
- Use only when correctly assembled and with safety devices and guards on the machine fully operational.