{{ name }}
Č. pol. {{ combinedCodeWithHighlight }}
Kód položky:
EAN/GTIN:
Číslo výrobcu:
Základní prvek HiPer-Drill 13,5
Č. pol.: 231620 13,5
Kód položky:
- Prevedenie: 12×D
- Stopka: ISO 9766
- Použite vrtáka: podmienené priečne vŕtanie; podmienené vŕtanie vo zväzku; podmienene šikmý výstup; podmienené strediace vŕtanie
- Vnútorné chladenie: áno
Podrobnosti o výrobku
Technické údaje
| Séria | HiPer Drill | |
| Prevedenie | 12×D | |
| Stopka | ISO 9766 | |
| Použite vrtáka | podmienené priečne vŕtanie; podmienené vŕtanie vo zväzku; podmienene šikmý výstup; podmienené strediace vŕtanie | |
| Počet rezných hrán Z | 2 | |
| Vnútorné chladenie | áno | |
| ⌀ rozsah Dc | 13,5 mm - 13,99 mm | |
| Úžitková dĺžka L1 | 168 mm | |
| ⌀ stopky Ds | 16 mm | |
| Dĺžka stopky Ls | 48 mm | |
| Upínacia skrutka | 231999 7IP (0,6 Nm) | |
| Celková dĺžka L | 239 mm | |
| Druh produktu | Vrták s vymeniteľnými doštičkami |
Identifikačné čísla a klasifikácie
| Číslo položky | 231620 13,5 | |
| EAN/GTIN | 4045197687647 |
Popis
Version:
- Very high feed rates and maximum performance due to optimally matched geometries and materials.
- Precise positioning of the cutter insert due to Vee insert seating and secure clamping by the centre bore.
- High concentricity when assembled.
- Shank support for optimum stability in operation.
Polished flutes.
Application:
For stationary and rotating use. For holes up to IT9 accuracy.
Note:
Further sizes up to ⌀ 50.99 mm available on request.
The insert screw must be replaced after every fifth change of cutter insert.
Reduce feed rates f by 10 % and vc values by 40 %.
For process reliability when using the drill, initial pilot drilling to 1.5×D with the drill No. 231600 with the same cutter insert size and type is necessary. The generation of a pilot hole improves process reliability.
Clamp in a hydraulic chuck (such as No. 302026 size 20) for optimum radial run-out.
For optimum stability, clamp the drill so the overhang is as short as possible.
For process reliability when using the drill, initial pilot drilling to 1.5×D with the drill No. 231600 with the same cutter insert size and type is necessary. The generation of a pilot hole improves process reliability.
The insert screw must be replaced after every fifth change of cutter insert.
Reduce feed rates f by 10 % and vc values by 40 %.
For process reliability when using the drill, initial pilot drilling to 1.5×D with the drill No. 231600 with the same cutter insert size and type is necessary. The generation of a pilot hole improves process reliability.
Clamp in a hydraulic chuck (such as No. 302026 size 20) for optimum radial run-out.
For optimum stability, clamp the drill so the overhang is as short as possible.
For process reliability when using the drill, initial pilot drilling to 1.5×D with the drill No. 231600 with the same cutter insert size and type is necessary. The generation of a pilot hole improves process reliability.