{{ name }}
Tuote nro. {{ combinedCodeWithHighlight }}
Tuotekoodi:
EAN / GTIN:
Valmistajan numero:
GARANT Diabolo TKM-pienoisjyrsin 1,5X6 mm
Tuote nro.: 201631 1,5X6
Tuotekoodi:
- Lastuava aine: TKM
- Standardi: Tehdasnormi
- tyyppi: H
- Tolerance nominal ⌀: 0 / −0,005
- No. of teeth Z: 2
Tuotetiedot
Tekniset tiedot
| Sarja | Diabolo | |
| Cutting edge ⌀ DC | 1.5 mm | |
| Pinnoitus | TiAlN | |
| Lastuava aine | TKM | |
| Standardi | Tehdasnormi | |
| tyyppi | H | |
| Tolerance nominal ⌀ | 0 / −0,005 | |
| No. of teeth Z | 2 | |
| Helix angle | 30 degrees | |
| Direction of infeed | horizontal, oblique and vertical | |
| Lastuamisleveys ae jyrsinnän aikana | täysuran työstösyvyys 1×D; 0,1×D särmäyksessä | |
| Shank | DIN 6535 HA to h5 | |
| Sisäjäähdytys | ei | |
| Flute length Lc | 2.3 mm | |
| Overhang length L1 incl. recess | 6 mm | |
| Recess ⌀ D1 | 1.44 mm | |
| Overall length L | 45 mm | |
| Shank ⌀ Ds | 4 mm | |
| Corner chamfer angle | 90 degrees | |
| Feed fz for slot milling in steel < 65 HRC | 0.015 mm | |
| Feed fz for side milling in steel < 65 HRC | 0.02 mm | |
| Cutting speed vc in steel < 65 HRC | 52 m/min | |
| Correction factor ap corr | 1 | |
| Värirengas | punainen | |
| Tuotetyyppi | Kulmajyrsin |
Tunnistenumerot ja Luokitukset
| Tuotekoodi | 201631 1,5X6 | |
| EAN / GTIN | 4045197932952 |
Käyttötaulukko
P
200
P
200
P
190
P
170
H
120
H
100
H
72
H
55
H
50
H
45
M
90
M
80
N
140
Kuvaus
Version:
GARANT Diabolo:
Special geometry, coating and carbide for hard machining in the high-performance field. Suitable even for machining electrolytic copper. Double-relief ground 2 chamfers hollow ground for high-precision hard machining.
Recess angle α = 16°.
Tolerances:
Special geometry, coating and carbide for hard machining in the high-performance field. Suitable even for machining electrolytic copper. Double-relief ground 2 chamfers hollow ground for high-precision hard machining.
Recess angle α = 16°.
Tolerances:
- Neck ⌀: D1 = 0 / -0.01 mm.
Note:
At greater tool overhang lengths, use a reduced value for ap!
Values for:
slots milled from solid: ap = 0.05×D×ap korr
side milling: ap = 0.1×D×ap korr
To calculate the feed rate vf please use the actual speed of the machine (the maximum possible speed)! e.g: vf = 18000 [rpm]× fz [mm/Z]× z
Values for:
slots milled from solid: ap = 0.05×D×ap korr
side milling: ap = 0.1×D×ap korr
To calculate the feed rate vf please use the actual speed of the machine (the maximum possible speed)! e.g: vf = 18000 [rpm]× fz [mm/Z]× z