{{ name }}
Artikelnummer {{ combinedCodeWithHighlight }}
Klantartikelnummer:
EAN/GTIN:
Nummer fabrikant:
GARANT Diabolo VHM-microfrees 1,2X20 mm
Artikelnummer: 201631 1,2X20
Klantartikelnummer:
- Snijmateriaal: VHM
- Norm: Fabrieksnorm
- Type: H
- Tolerance nominal ⌀: 0 / −0,005
- No. of teeth Z: 2
Productdetails
Technische gegevens
| Serie | Diabolo | |
| Cutting edge ⌀ DC | 1.2 mm | |
| Coating | TiAlN | |
| Snijmateriaal | VHM | |
| Norm | Fabrieksnorm | |
| Type | H | |
| Tolerance nominal ⌀ | 0 / −0,005 | |
| No. of teeth Z | 2 | |
| Helix angle | 30 degrees | |
| Direction of infeed | horizontal, oblique and vertical | |
| Ingrijpingsbreedte ae bij freesoperatie | Volle groef snijdiepte 1×D; 0,1×D bij kanten | |
| Shank | DIN 6535 HA to h5 | |
| Inwendige koeling | nee | |
| Flute length Lc | 1.8 mm | |
| Overhang length L1 incl. recess | 20 mm | |
| Recess ⌀ D1 | 1.14 mm | |
| Overall length L | 60 mm | |
| Shank ⌀ Ds | 4 mm | |
| Corner chamfer angle | 90 degrees | |
| Feed fz for slot milling in steel < 65 HRC | 0.01 mm | |
| Feed fz for side milling in steel < 65 HRC | 0.015 mm | |
| Cutting speed vc in steel < 65 HRC | 38 m/min | |
| Correction factor ap corr | 0.12 | |
| Gekleurde ring | rood | |
| Producttype | Hoekfrezen |
Identificatienummers en classificaties
| Artikelnummer | 201631 1,2X20 | |
| EAN/GTIN | 4045197932921 |
Toepassingstabel
P
200
P
200
P
190
P
170
H
120
H
100
H
72
H
55
H
50
H
45
M
90
M
80
N
140
Omschrijving
Version:
GARANT Diabolo:
Special geometry, coating and carbide for hard machining in the high-performance field. Suitable even for machining electrolytic copper. Double-relief ground 2 chamfers hollow ground for high-precision hard machining.
Recess angle α = 16°.
Tolerances:
Special geometry, coating and carbide for hard machining in the high-performance field. Suitable even for machining electrolytic copper. Double-relief ground 2 chamfers hollow ground for high-precision hard machining.
Recess angle α = 16°.
Tolerances:
- Neck ⌀: D1 = 0 / -0.01 mm.
Note:
At greater tool overhang lengths, use a reduced value for ap!
Values for:
slots milled from solid: ap = 0.05×D×ap korr
side milling: ap = 0.1×D×ap korr
To calculate the feed rate vf please use the actual speed of the machine (the maximum possible speed)! e.g: vf = 18000 [rpm]× fz [mm/Z]× z
Values for:
slots milled from solid: ap = 0.05×D×ap korr
side milling: ap = 0.1×D×ap korr
To calculate the feed rate vf please use the actual speed of the machine (the maximum possible speed)! e.g: vf = 18000 [rpm]× fz [mm/Z]× z